Reverse faults occur in areas where the crust is being shortened such as at a convergent boundary. Maximum magnitudes along many normal faults are even more limited because many of them are located along spreading centers, as in Iceland, where the thickness of the brittle layer is only about six kilometres (3.7 mi). Earthquakes associated with normal faults are generally less than magnitude 7. Normal faults occur mainly in areas where the crust is being extended such as a divergent boundary. The longest earthquake ruptures on strike-slip faults, like the San Andreas Fault ( 1857, 1906), the North Anatolian Fault in Turkey ( 1939), and the Denali Fault in Alaska ( 2002), are about half to one third as long as the lengths along subducting plate margins, and those along normal faults are even shorter. Examples are the earthquakes in Alaska (1957), Chile (1960), and Sumatra (2004), all in subduction zones. The maximum observed lengths of ruptures and mapped faults (which may break in a single rupture) are approximately 1,000 km (620 mi). Rocks hotter than about 300 ☌ (572 ☏) flow in response to stress they do not rupture in earthquakes. The topmost, brittle part of the Earth's crust, and the cool slabs of the tectonic plates that are descending into the hot mantle, are the only parts of our planet that can store elastic energy and release it in fault ruptures. Many earthquakes are caused by movement on faults that have components of both dip-slip and strike-slip this is known as oblique slip. Normal and reverse faulting are examples of dip-slip, where the displacement along the fault is in the direction of dip and where movement on them involves a vertical component. There are three main types of fault, all of which may cause an interplate earthquake: normal, reverse (thrust), and strike-slip. Therefore, earthquakes lower the Earth's available elastic potential energy and raise its temperature, though these changes are negligible compared to the conductive and convective flow of heat out from the Earth's deep interior. Most of the earthquake's energy is used to power the earthquake fracture growth or is converted into heat generated by friction. It is estimated that only 10 percent or less of an earthquake's total energy is radiated as seismic energy. This process of gradual build-up of strain and stress punctuated by occasional sudden earthquake failure is referred to as the elastic-rebound theory. This energy is released as a combination of radiated elastic strain seismic waves, frictional heating of the fault surface, and cracking of the rock, thus causing an earthquake. This continues until the stress has risen sufficiently to break through the asperity, suddenly allowing sliding over the locked portion of the fault, releasing the stored energy. Once the fault has locked, continued relative motion between the plates leads to increasing stress and, therefore, stored strain energy in the volume around the fault surface. Most fault surfaces do have such asperities, which leads to a form of stick-slip behavior. The sides of a fault move past each other smoothly and aseismically only if there are no irregularities or asperities along the fault surface that increases the frictional resistance. Tectonic earthquakes occur anywhere in the earth where there is sufficient stored elastic strain energy to drive fracture propagation along a fault plane. The epicenter is the point at ground level directly above the hypocenter. An earthquake's point of initial rupture is called its hypocenter or focus. Earthquakes are caused mostly by rupture of geological faults but also by other events such as volcanic activity, landslides, mine blasts, and nuclear tests. In its most general sense, the word earthquake is used to describe any seismic event-whether natural or caused by humans-that generates seismic waves. When the epicenter of a large earthquake is located offshore, the seabed may be displaced sufficiently to cause a tsunami. The word tremor is also used for non-earthquake seismic rumbling.Īt the Earth's surface, earthquakes manifest themselves by shaking and displacing or disrupting the ground. The seismicity at a particular location in the Earth is the average rate of seismic energy release per unit volume. The seismic activity of an area is the frequency, type, and size of earthquakes experienced over a particular time. Earthquakes can range in intensity, from those that are so weak that they cannot be felt, to those violent enough to propel objects and people into the air, damage critical infrastructure, and wreak destruction across entire cities. An earthquake (also known as a quake, tremor or temblor) is the shaking of the surface of the Earth resulting from a sudden release of energy in the Earth's lithosphere that creates seismic waves.
0 Comments
Leave a Reply. |